Fire Door Sizes and Thickness Guide — FD30, FD60 & FD120

What size and thickness should a fire door be? This guide gives leaf thicknesses by rating, common fire door sizes used in India, inch-to-mm conversions (such as the 27-inch fire door), and how to measure an opening before you ask for a quote.

Ready to price? See Wedge fire doors or send your schedule.

Cutaway of a Wedge fire door showing core thickness
44–46 mmtypical FD30 leaf (timber / steel)
50–54 mmtypical FD60 leaf (steel / timber)
56–60 mmtypical FD120 leaf
1,200 × 2,400 mmlargest single leaf in the Wedge range

Quick answer

A fire door is thicker than an ordinary door because its core must hold back fire and heat. In the Wedge range, FD30 leaves are 44 mm (timber) or 46 mm (steel), FD60 leaves are 54 mm (timber) or 50 mm (steel), and FD120 leaves are 56–60 mm. Common Indian opening heights are 2,100 mm, with single leaves from about 750 mm to 1,200 mm wide. The final size is always limited by the test report that covers the door.

Fire door thickness by rating

RatingLeaf thickness (Wedge build-up)CoreTypical use
FD30 — 30 minutes44 mm timber · 46 mm steelHDRW 850 rockwool or FD30 board coreFlat entrances, corridors, service rooms
FD60 — 60 minutes54 mm timber · 50 mm steelCalcium silicate faced coreStaircases, lift lobbies, refuge areas, hospital wards
FD120 — 120 minutes56–60 mmDouble-board core, MgO or calcium silicateExit stairs, basements, plant and electrical rooms

Thickness alone does not make a door fire-rated. The leaf, frame, core, seals, glazing and hardware must match a doorset test report.

Is a 35 mm door a fire door?

Usually not. 35 mm is the standard thickness of ordinary internal doors in UK imperial sizing. Fire-rated timber leaves are normally thicker — around 44 mm for FD30 and 54 mm for FD60 — because the core needs more mass. A 35 mm door should only be treated as fire-rated if a test report covers that exact leaf. If you have 35 mm doors on an escape route, ask us about replacement doorsets or an upgrade.

Common fire door sizes in India

DoorTypical leaf widthTypical heightWhere used
Single leaf — service / shaft750–900 mm2,100 mmShafts, risers, stores, service rooms
Single leaf — corridor / flat entrance900–1,000 mm2,100 mmFlat entrances, hotel rooms, offices
Single leaf — exit / stair1,000–1,200 mm2,100–2,400 mmStaircases, lift lobbies, exits
Double leaf2 × 750 to 2 × 900 mm2,100–2,400 mmHospital corridors, lobbies, plant rooms

These are common project sizes, not a fixed standard. Wedge makes fire doors to your opening sizes within the tested range: single leaves up to 1,200 × 2,400 mm and double leaves up to 2 × 900 × 2,400 mm.

Fire door sizes in inches and mm (UK standard leaves)

Many drawings and imported doors use UK imperial leaf sizes. Height is 1,981 mm (78 inches / 6 ft 6 in).

Leaf width (inches)Leaf width (mm)Full leaf size (mm)
24″610 mm1,981 × 610
27″686 mm1,981 × 686
30″762 mm1,981 × 762
33″838 mm1,981 × 838
36″915 mm1,981 × 915

A 27-inch fire door is a leaf about 686 mm wide by 1,981 mm high (2 ft 3 in × 6 ft 6 in). In India, an equivalent opening is usually made as a 700–750 mm leaf to suit the frame and wall. Tell us the opening size and we will match it.

How to measure for a fire door

  1. Structural opening: measure the masonry or RCC opening width and height at three points; use the smallest.
  2. Wall thickness: the frame depth must suit the wall (for example 100, 150 or 230 mm).
  3. Clear opening: the usable width with the door open at 90° — this is what the fire code checks on escape routes.
  4. Swing and hardware: note the opening direction, closer, panic bar and any vision panel.
  5. Floor finish: give the finished floor level so the bottom gap is right.

Fire door performance depends on the gaps. Wedge doorsets are fitted with a perimeter gap of 3 mm ± 1 mm so the INTUF intumescent seal can close it in a fire.

What width does the fire code ask for?

NBC 2016 Part 4 (clause 4.7.1) sets a minimum clear width of 1,000 mm for exit doors in most buildings, and NBCS 2026 calls for certified doorsets with intumescent seals on exit doors. Exact widths depend on occupancy and occupant load, so confirm them with your architect or fire consultant. See our NBCS 2026 fire door checklist.

Vision panels and double doors

  • Vision panels use fire-rated glass and Wedge ceramic glazing tape; the glass size must be within the tested size.
  • Double doors need a selector or coordinator so leaves close in the right order, and seals on the meeting edges.
  • Over-panels and side-panels must be covered by the same test evidence as the leaf.

Get a fire door size checked and priced

Send opening sizes, wall thickness, rating and quantity. We confirm the leaf size, thickness and test report, and quote within two working days.

Fire door size FAQs

What is the standard size of a fire door in India?

There is no single size. Common project sizes are 900–1,000 mm × 2,100 mm for single doors and 2 × 750 to 2 × 900 mm × 2,100 mm for double doors. Fire doors are made to the opening, within the size range of the test report.

How thick is an FD30 fire door?

About 44 mm for a timber leaf and 46 mm for a steel leaf in the Wedge range.

How thick is an FD60 fire door?

About 54 mm for a timber leaf and 50 mm for a steel leaf in the Wedge range.

How thick is an FD120 fire door?

56–60 mm, with a double-board magnesium oxide or calcium silicate core.

Is a 35 mm door fire rated?

Normally no. 35 mm is the usual thickness of ordinary internal doors. Fire-rated timber leaves are usually 44 mm or thicker, and only a test report can confirm a rating.

What is a 27 inch fire door in mm?

About 686 mm wide by 1,981 mm high (2 ft 3 in × 6 ft 6 in).

Can fire doors be made to any size?

They can be made to your opening sizes up to the maximum the test report allows. In the Wedge range that is 1,200 × 2,400 mm for a single leaf and 2 × 900 × 2,400 mm for a double.

Related

Send your fire door sizes

Opening sizes, wall thickness, rating and quantity — we confirm the right leaf size and thickness and send a priced offer within two working days.

Wedge Doors is the door division of Wedge Industries Limited, the Faridabad manufacturer of fire-resistant boards, rockwool cores and intumescent seals. Insulation and fire protection materials: wedgeinsulation.com · Fire door cores and seals: fire door components.

Scroll to Top